18 November 2026 7 min read
Cleaning timber look tiles: everyday care, grout and what to avoid
The floor looks like spotted gum, so the first instinct is to treat it like spotted gum: a timber floor cleaner, a soft polish, maybe a coat of something once a year. None of that belongs on a tile, and some of it leaves a film that makes the floor look dull and feel slippery.
Here is how to clean timber look tiles day to day, which cleaners to keep and which to skip, and why most of the care goes into the grout.
Why the tile needs so little
Our timber look tiles are glazed ceramic. The glaze is fired on in the kiln and is the surface you walk on and mop. The body under it absorbs 6 to 8% water. That puts it in group BIIb of EN 14411, the standard that classifies ceramic tiles by how they are made and how much water they absorb. That is the normal range for glazed ceramic, and the glaze on top is what meets the spills.
So there is no coating to renew, no sanding and no sealing of the tile face. What is left is keeping grit off it and keeping the joints clean.
Everyday cleaning
- Sweep or vacuum first. Grit from the yard or the beach is what dulls any floor. Mopping before sweeping just pushes it around.
- Damp mop with a pH neutral cleaner. Laticrete's Australian care sheet recommends a clear pH neutral cleaner for routine maintenance of tile and grout. Use it diluted as the label says.
- Wring the mop well. The same sheet notes that damp mopping can leave dirt residue on grout. Change the water when it turns grey, and on a dirty floor pick up the mop water before it dries.
- Let it dry before walking on it. A wet tile is more slippery than a dry one, even in Matt Texture.
Matt Texture needs a slightly different touch
Matt Texture has grain relief you can feel. Dirt sits in the low points of the grain, so a microfibre flat mop or a soft brush lifts it better than a sponge mop, which skims over the top. Every few weeks, scrub the high-traffic paths with a soft nylon brush and rinse.
What to avoid
- Timber floor products, waxes and polishes. They are made for coated boards. On a glaze they build a film that holds dirt and changes the grip.
- Steel wool and harsh scourers. Use a nylon pad instead.
- Strong chemicals as a habit. Bleach and strong acids are not everyday cleaners for tile and cement grout. Keep specialist products for specialist jobs.
- Untested products. Laticrete advises testing any cleaning product on a small, hidden area first and letting it dry. A spare tile or an offcut in the garage is the easiest place to test.
The grout is where the work is
Grout is a cement-based joint between the tiles, and it is the part of the floor that stains. Laticrete states plainly that cement grouts are not self-cleaning or totally stain-resistant, and that wiping up spills quickly is what keeps them looking right.
- Wipe spills straight away. Red wine, coffee, oil and pet accidents sit on the glaze but can soak into the grout if left.
- Ask your tiler about a sealer for cement grout. It gives you more time to wipe up a spill. It is not a substitute for cleaning.
- Think about grout before installation. A grout in a tone close to the tile hides everyday marks better than white. Ask your tiler whether a stain-resistant grout suits the room, especially kitchens and homes with dogs.
Room by room
Kitchen
Cooking grease builds up in front of the cooktop. Laticrete suggests an alkaline cleaner for grease soiling, followed by a rinse. Our post on timber look tiles in an open-plan kitchen covers choosing the floor itself.
Bathroom, ensuite and laundry
Soap scum and hard water marks build up around the shower and the floor waste. A squeegee after each shower helps, and a product made for hard water deposits takes off what is left. See timber look tiles for bathrooms, ensuites and laundries for surfaces and waterproofing.
Entry and hallway
This is where grit arrives. Put mats inside and outside the door and vacuum more often than you mop. In a house with dogs, our post on timber look tiles with dogs and kids has more on paws and accidents.
Alfresco and verandah
Sweep with a stiff outdoor broom, hose off, and scrub leaf and berry stains before they set into the grout. Matt Texture is the surface to use outside, and it cleans the same way.
After installation
The first clean belongs to your tiler. Metro's laying guide asks for excess grout to be cleaned off as the joints are filled, so the surface should be handed over clear. If a light grout haze remains, ask the tiler what the grout maker recommends for it, and give the grout its full curing time before any strong cleaner goes near it.
Keep a spare box
Ceramic is hard, but a cast iron pan dropped from the bench can chip a tile. Keep a few spare tiles from the same batch and calibre code so a damaged plank can be lifted and replaced on its own. Write the design name and size on the box. Every Metro tile has a curve edge formed in the mould, and a replacement plank set with the same 3 to 5 mm joint blends back in.
Where real timber is easier
Timber has no grout lines to keep clean, and a worn timber floor can be sanded back to new. Tile asks less of you week to week, but the joints need some attention for the life of the floor, and a chipped tile is replaced rather than repaired.
The short version
Sweep, damp mop with a pH neutral cleaner, wipe spills before they reach the grout, and skip anything made for timber. For a floor that is easy to keep, choose Matt Texture in a mid tone with a matching grout. The 200x1200mm range has the most Matt Texture designs, and every size is in our downloadable catalogue. Browse every design, or talk to our team about samples.
Planning timber look tiles for your home?
Tell us the room and the size you have in mind. Our team replies within 24 to 48 hours, and we can post you a sample first so you can see the surface in your own light.
Frequently asked questions
What is the best way to clean timber look tiles?
Sweep or vacuum first, then damp mop with a diluted pH neutral cleaner and a well wrung mop. On Matt Texture, a microfibre flat mop or soft brush gets into the grain better than a sponge mop.
Do timber look tiles need sealing?
No. The tile face is a fired glaze and needs no sealer. Cement grout is different: a grout sealer can help it resist stains, so ask your tiler whether one suits your room.
Can I use vinegar to clean timber look tiles?
Not as an everyday cleaner. A pH neutral cleaner is the routine choice for tile and cement grout. Keep acidic products for specific jobs such as hard water marks, and test them on a spare tile first.
Can I use timber floor cleaner or polish on timber look tiles?
No. Timber products are made for coated boards. On a glazed tile they leave a film that holds dirt and can change how slippery the floor feels.
How do I get stains out of the grout?
Wipe spills straight away. For a set stain, scrub the joint with a nylon brush and a cleaner made for grout, then rinse. Test any stronger product on a hidden area first.
How do I clean Matt Texture timber look tiles?
The same way as any tile, with one change: use a microfibre flat mop or a soft nylon brush, because dirt sits in the low points of the grain relief.